Tutorial: Replacing stiff motor wires with flexible ones — no more breaking wires [BR1103B]

Disclosure: This post may contain affiliate links, meaning I get a commission if you decide to make a purchase through my links, at no cost to you.

By | September 8, 2017

UPDATE: There is a follow up post on how to remove the stiff wires alltogether.

I have been building micro brushless quadcopters like my pepperFIISH for a while now. Over the last builds it became more and more clear that one of the weakest spots are actually the motor wires: Most of the small brushless motors come with stiff, single strand copper wires covered in heat shrink tubing. Most of the time this wire breaks due to vibration directly at the soldering spot at ESC pad. Often this is due to previous damage caused by minimal cuts occurring while stripping the isolation but it also happens to perfect solder joints.

The root of the problem is the single stranded and stiff wire. Replacing it with a flexible multi strand silicone cable helps a lot. In this tutorial I am going to show you how to replace these cables. Along the way you will also learn a nice trick to remove the cable isolation without leaving cuts on the wires. I am going to write this tutorial based on a Racerstar BR1103B motor but in principle this can be applied to all motors. If you use bigger motors make sure to use the proper sized silicone wire. Measure the single stranded wire thickness and use this AWG chart to lookup the best matching AWG size. I measured the wires of the 8000KV BR1103B to be 0.22mm in diameter and the perfect match would be 31 AWG. This is not common and as thicker wires are generally better I choose 30 AWG for this motor.

You will need the following items:

[1] Cut the wires

Even though removing the wires altogether and soldering the silicon wires directly to the motor coils would be the cleanest solution, we are going to cut and attach the wires on the outside as this saves us a tremendous amount of work (disassembly of the bell, removal of glue, messing around with the tiny coil wires,…).

Start by cutting the wires at a distance you feel comfortable with. I usually cut the wires at 1cm distance but you might want to start with some more length. Just make sure to remember the exact length where you cut it, it will become important in one of the following steps.

[2] Overstretch the isolation

Now comes a handy trick: Remember, the isolation is heat shrink tubing, mechanically stretched heat shrink tubing contracts on application of heat. We are going to exploit this property in order to get clean wire ends without cut marks. Take a tweezer or pliers and gently pull and overstretch the isolation 4-5 mm as shown in the next picture:

[3] Cut the isolation

Now cut the wires again at the same distance you did the initial cut. If done properly you will only cut the (overstretched) isolation as the wire does not extend to that distance

[4] Apply heat

Now apply some heat to the wire ends. You can either use a hot air gun or a gas lighter for this:

The overstretched heat shrink tubing will now contract and expose some millimeters of the bare wire!

[5] Tin coating

Cut three 5 cm long pieces of your silicone wire and strip 2mm of the isolation. Use your soldering iron to tin the silicon wire and the bare wire ends of your motor.

[6] Solder

Cut any excess wire and solder the single ends together.

[7] Heat shrink tubing

You’re almost done. Cut 5mm long pieces of heat shrink tubing and use heat to shrink them in place. Your final result should look similar to this:

Repeat this three times for the other motors and you are done! Or five if you are building a hexacopter 😉

In order to prevent the point of cable attachment from breaking due to vibrations, make sure to attach this spot to the frame. I use thin pieces of duct tape or multiple turns of thin thread for this.

Happy flying!

3 thoughts on “Tutorial: Replacing stiff motor wires with flexible ones — no more breaking wires [BR1103B]

  1. Sam

    Just for fun, I decided to sacrifice a motor to science and to see if I could do better by attaching the new wires under the bell. I failed, but I learned some key things in the process that I wanna add to this.
    The adhesive used is not very strong and more brittle than hot glue. I was most worried about that step but it was easily peeled and chipped away. Most importantly, the wires that the br1103b’s come with are nothing more than two-conductor extensions of the actual windings. Might explain why the heat shrink slides off them so easily when you strip them. Check out a couple photos here:
    And that means the wires are enameled way back inside the bell, so in order for solder to stick you have to scrape them with a blade (not recommended) or some other strategy I need to know, because that quickly kills the amount of strain the wires will take.
    Strain relief is super critical here. The new wires need to be epoxied down immediately. One of mine failed before I could finish heat shrinking it. Most likely due to scraping then becoming brittle from solder.

    Reply
    1. fishpepper Post author

      Thanks for your suggestion! I had to try this on my own… And indeed, it works like a charm!
      You can find my updated post here.

      Reply

Leave a Reply to Sam Cancel reply

Your email address will not be published. Required fields are marked *